Discovering Plumbing Basics is Vital for Bathtub Installation
Discovering Plumbing Basics is Vital for Bathtub Installation
Blog Article
On this page down the page you can find a lot of dependable details all about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bathtub isn't exactly brain surgery, but it does require strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old tub with a new one is also a reasonably challenging project. If the old bathtub is readily available, the job can move rapidly; if you have to open a wall to get rid of the old bathtub as well as position the brand-new bath tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. Make certain you have certified yourself for the task and are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is far better to consider utilizing one before you start. Chances are you may need a specialist plumber to make tube links.
This article will assist you mount a new bath tub in your restroom if you have actually already acquired a new bathtub and do not need to transform the setup of your previous water pipes.
Your devices as well as material list should comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted gain access to that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin making certain that the washing machines are in location in between the tap as well as the sink. Secure the tap in place with the producer supplied backnut. When the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also changing the feet on the tub up until the spirit level reads level.
To mount taps, fit the bottom of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the tub and likewise check the overflow outlet and also the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of once as this will certainly resolve it right into its last placement.
Preparing for the Installation
First of all, the supporting framework supplied with the bath ought to be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to stop strain on the bath tub.
Fit the adaptable tap adapters to the bottom of both faucets using 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to split an inflexible seal, creating the water to pass through the wall between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can break fairly early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
I'm just very enthusiastic about How to Install a Bathtub Yourself and I hope you liked my page. Enjoyed our piece of writing? Please share it. Help somebody else discover it. I love reading our article about How to Install a Bathtub.
Get the best, ring us! Report this page